You open a song in a chord app, and most of the chart sounds right. Then the chorus hits a chord that's clearly wrong, or a whole section reads minor when it sounds major.

That happens with every chord detection app, including ours. We make GigaChords, so the fixes below use it, but the reasons apply to any app. Once you know them, the wrong chords are quick to find and fix.

What a chord app actually hears

A chord app never sees a chord sheet. It hears the whole mix at once: voice, drums, bass, guitars, keyboards and effects. At each moment it picks out the notes sounding together, decides which chord they most likely form, and marks where each chord starts and ends.

On most songs, that gets most of the chart right. These are the places where it goes wrong.

Seven common reasons

1. Chords that share most of their notes

C major and A minor share two of their three notes. A and A7, or C and Cmaj7, differ by a single note. If that note is quiet in the mix, the app has to guess.

What to do: if a chord sounds almost right, try its close relatives first.

2. The bass plays a different note

A G chord with B in the bass (written G/B) sounds different from a plain G. A bass line that walks between chords can also make one chord sound like another.

What to do: slow the section down and listen only to the lowest notes. If the chart's chord doesn't match the bass, that's usually the spot to fix.

3. Busy arrangements

Strings, synth pads, backing vocals and the melody all add notes that aren't part of the chord. A long sung note held over a chord change can make the app hear a chord that isn't there.

What to do: loop the bar and slow it down. With fewer notes going by at once, the real chord is easier to hear.

4. Power chords and distortion

Many rock songs use power chords: just the root and the fifth, with no third. The third is the note that makes a chord major or minor, so without it, the app has to pick one. Distortion adds overtones that blur the sound further.

What to do: check the major or minor against the vocal melody or the bass. Often either one works under a power chord, and you can pick the one that sounds best with the voice.

5. Very short chords and changes that land early or late

Passing chords that last half a beat are easy to miss. A chord change can also land slightly early or late on the timeline, especially in live recordings where the tempo drifts.

What to do: loop the bar and listen for movement. If a change lands early or late, select the cells around it and set each one to the chord you hear.

6. Unusual chords

Chord detection leans on musical context. A chord that's rare in the song's key, like a B♭ major in a song in C, is easier to misread as a more common neighbor.

What to do: when a chord in the chart sounds "safe" but the song sounds surprising at that moment, trust your ear and try the less expected chord.

7. Recordings that aren't in standard tuning

Some bands tune down a half step, and some older recordings play slightly fast or slow. The chart names the chords you actually hear. So if a band tuned down a half step and played an E shape, the chart shows E♭.

What to do: play the chart as written if you're in standard tuning. If you'd rather use the band's shapes, tune down a half step yourself and play each chord a half step higher (an E shape where the chart says E♭).

How to fix the chart in GigaChords

  1. Loop and slow down the spot. The chart stays in sync with the song at any speed.
  2. Hear the chord. Turn on chord sound, and each new chord plays once on your instrument as the song reaches it. Compare it with the recording.
  3. Change the chord. Select a chord cell and choose the chord you hear. If the same mistake repeats, "Apply to similar places" previews the same change in matching spots, and you choose which ones to apply.
  4. Simplify if you want to. If the chart shows chords like Cmaj7 and you'd rather play C, "Simplify chord names" changes how they're shown without re-analyzing the song.
  5. Fix timing that drifts. If the chart and the song drift apart toward the end, the gradual correction in the timing settings can bring them back together.
  6. Save the song. It opens again with your corrections, without a new analysis.

If a song comes out badly wrong, you can tell us with "Send chord feedback" in the app. It sends the chord chart for our review, not the audio.

How accurate is chord detection?

It depends more on the recording than on anything else. A clear recording of a guitar or piano with one voice is much easier than a dense, heavily produced mix. Treat any chart, from any app, as a strong first draft, and check it by ear before you learn it.

Questions

Why does my chord app show the wrong chords?
The app hears the whole mix, not a chord sheet. Chords that share notes, bass notes under a chord, busy arrangements, power chords, very short chords, unusual chords and non-standard tuning can all lead it to the wrong chord.
Why does the chart say minor when the song sounds major?
Usually because the chord's third is quiet or missing, as in a power chord, or because another instrument adds a note that suggests minor. Check it against the vocal melody and the bass.
Why is every chord a half step off?
The recording is probably not in standard tuning. Many bands tune down a half step. The chart names the sounding chords, so play it as written in standard tuning, or tune down and play each chord a half step higher.
Can I correct the chords in GigaChords?
Yes. Change any chord, apply the same fix to similar places if you want, and save the version you trust.
Does GigaChords upload my song to find the chords?
No. The analysis runs on your device, and it works with your own song files and microphone recordings.
Is GigaChords free?
You can start free, with 3 full-song analyses a month and up to 3 saved songs.